Direct purchasing of our products on our website is not possible. We are working together with a world-wide network of wholesalers to get our products distributed.
Check out our Dealer page for a wholesaler or dealer near you:
We recommend using 4 point tie-downs to transport your motorcycle. 2 in the front on each side and 2 in the rear on each side. Always lash down at a slight forward angle to your direction of travel. This ensures that the motorcycle remains firmly secured in the front wheel stand during transport.
The TyreFix is suitable for both front and rear tires. Provided there is enough space and no interference with e.g. a front fender.
To choose the correct SteadyStand for a 14 inch tire size depends on a couple of factors. To give you the best solution you can use the following flowchart:
To explain this some further:
For a tire size of 14 inch with a width of 80 to 90 mm you can use the SteadyStand® Scooter or for transport only the SteadyStand® Fixed Scooter.
You would need to set the SteadyStand in the furthest 13 inch position:
If you are planning to use the SteadyStand for transportation only of your motorcycle or scooter, and your tire width is between 90 and 130 mm you can opt for the SteadyStand® Fixed which is suitable for wheel sizes from 10 to 19 inches, tyre width from 90 to 130 mm.
For a tire size of 14 inch with a width of 100 to 130 mm you can use the SteadyStand® but you would need to set the SteadyStand in the nearest 15 inch position:
If you are planning to use the SteadyStand for transportation only of your motorcycle or scooter, and your tire width is between 90 and 130 mm you can opt for the SteadyStand® Fixed which is suitable for wheel sizes from 10 to 19 inches, tyre width from 90 to 130 mm.
We have a range of SteadyStands suitable for almost any tire size. For parking we recommend our regular SteadyStand, for transport we recommend our ‘Fixed’ version which are designed to be mounted onto a surface.
SteadyStand® Scooter
SteadyStand® Fixed Scooter
SteadyStand® Multi
SteadyStand® Multi Fixed
SteadyStand® Cross
SteadyStand® Cross Basic
SteadyStand® Cross Flex
Visit all our SteadyStand products:
Motorcycle Stand
To use our SteadyStands on your rear wheel, we recommend our SteadyStand Multi, which is more suitable for wider tyres. The SteadyStand Multi is suitable for tyres from 15 to 21 inches and 90 to 200 mm wide.
SteadyStand® Multi
SteadyStand® Multi Fixed
To choose the correct SteadyStand for a 14 inch tire size depends on a couple of factors. To give you the best solution you can use the following flowchart:
To explain this some further:
For a tire size of 14 inch with a width of 80 to 90 mm you can use the SteadyStand® Scooter or for transport only the SteadyStand® Fixed Scooter.
You would need to set the SteadyStand in the furthest 13 inch position:
If you are planning to use the SteadyStand for transportation only of your motorcycle or scooter, and your tire width is between 90 and 130 mm you can opt for the SteadyStand® Fixed which is suitable for wheel sizes from 10 to 19 inches, tyre width from 90 to 130 mm.
For a tire size of 14 inch with a width of 100 to 130 mm you can use the SteadyStand® but you would need to set the SteadyStand in the nearest 15 inch position:
If you are planning to use the SteadyStand for transportation only of your motorcycle or scooter, and your tire width is between 90 and 130 mm you can opt for the SteadyStand® Fixed which is suitable for wheel sizes from 10 to 19 inches, tyre width from 90 to 130 mm.
Before purchasing a U-Turn Motor Mover, investigate if your motorcycle meets all the requirements and if your space of operation is suitable.
The U-Turn Motor Mover is designed for maneuvering only. Do not store the motorcycle on the U-Turn Motor Mover in the lifted position for long periods of time. Release the lever after maneuvering to lower te motorcycle onto the floor. For first time adjustment and operation two people are recommended. A smooth surface for maneuvering the U-Turn Motor Mover is recommended, uneven tiles or floors might damage the wheels.
Our U-Turn Motor Mover L is
Our U-Turn Motor Mover XL is
The maximum length and wheel dimensions are based on the limits of the operational design, e.g. if the motorcycle is too long, the lift handle will interfere with the rear fender or tire.
We recommend a smooth, even surface for our Motor Movers to allow for easy manoeuvring and to prevent damage to the wheels.
We do not recommend that you leave your bike on the U-Turn Motor Mover for long periods of time (e.g. during the winter). You can leave the U-Turn Motor Mover in place, but use the handle to release the pressure and ensure that the bike rests on its own.
